Electrochemical behavior of gold and its associated minerals in alkaline thiourea solutions

Electrochemical measurements were conducted to study the electrochemical behavior of gold (Au) and its commonly associated minerals in alkaline thiourea solutions. The results indicated that without addition of any stabilizer, selective dissolution of Au from stibnite and pyrite was only possible at relatively low thiourea concentrations. As Na₂SiO₃ was added, pyrite started to become active and an oxidation peak appeared; the oxidation peaks of arsenopyrite and chalcocite appeared earlier than that of Au. The chalcocite peak shifted in the positive direction and the peak current increased. Stibnite did not show an oxidation peak and its current was nearly zero. Adding Na₂SiO₃ favored the selective dissolution of Au when its minerals were associated with chalcocite and stibnite. At pH 12, the Au anode dissolution peak current increased with stabilizer concentration. At 0.38 and 0.42 V and for Na₂SiO₃ concentration below 0.09 M, the current density continuously increased with Na₂SiO₃ concentration. The Na₂SiO₃ concentration had to be adequate to stabilize thiourea. When the potential was higher than 0.42 V, the surface of the Au electrode started to passivate. With an additional increase in potential, the presence of Na₂SiO₃ could not stop the inevitable decomposition of thiourea.     

Corrosion behavior of high-strength spring steel for high-speed railway

The corrosion resistance and evolution of corrosion products in medium-carbon high-strength spring steels were investigated in a neutral salt spray (5wt% NaCl solution). A formation model of γ-FeOOH and a transformation model describing the conversion of γ-FeOOH to α-FeOOH were constructed. The results indicated that, at the initial corrosion stage, the corrosion resistance was gradually improved with the addition of Cr; however, with the addition of alloying element V, the corrosion resistance decreased. These results were attributed mainly to the initial corrosion stage being closely related to the matrix microstructure parameters such as grain-boundary character and dislocation density. After the rust layer was formed at a later corrosion stage, the corrosion resistance was reinforced with the addition of Cr and V because Cr strongly influenced the composition, structure, and morphology of the corrosion products. The results presented herein show that Cr was conducive to the transformation of γ-FeOOH into α-FeOOH. Moreover, V and Cr exhibited obvious synergy and were enriched in the inner layer of the corrosion products.     

Improvement of microstructure and corrosion properties of friction stir welded AA5754 by adding Zn interlayer

This study investigated the effect of Zn foil layers on the microstructure and corrosion characteristics of friction stir welded aluminum alloy 5754. Samples of various joints were prepared by applying different rotational and welding speeds, and their microstructures were evaluated via a metallographic technique and scanning electron microscopy equipped with energy-dispersive X-ray spectroscopy elemental analysis. The anticorrosion behavior of joints in the absence and presence of a Zn interlayer was studied by cyclic potentiodynamic polarization test in 3.5wt% NaCl aqueous solution, and sound welds were obtained in the presence of the Zn interlayer foil. The results revealed that the joint made at a rotational speed of 800 r/min and traveling speed of 15 mm/min achieved a chemical composition identical to that of aluminum alloy 7xxx series, and as such, it showed the best resistance to corrosion.     

Alkaline digestion behavior and alumina extraction from sodium aluminosilicate generated in pyrometallurgical process

In pyrometallurgical process, Al-and Si-bearing minerals in iron and aluminum ores are easily transformed into sodium aluminosilicates in the presence of Na₂O constituents, which alters the leaching behaviors of Al₂O₃ and SiO₂. It was confirmed that sodium aluminosilicates with different phase compositions synthesized at various roasting conditions were effectively digested in the alkaline digestion process. Under the optimum conditions at temperature of 100-120℃, liquid-to-solid ratio (L/S) of 10:2 mL/g, caustic ratio of 4, and Na₂O concentration of 240 g/L, the actual and relative digestion ratio of Al₂O₃ from the synthesized sodium aluminosilicates reached maximums of about 65% and 95%, respectively, while SiO₂ was barely leached out. To validate the superior digestion property of sodium aluminosilicate generated via an actual process, the Bayer digestion of an Al₂O₃-rich material derived from reductive roasting of bauxite and comprising Na_1.75Al_1.75Si_0.25O₄ was conducted; the relative digestion ratio of Al₂O₃ attained 90% at 200℃.     

Process mineralogy characteristics of acid leaching residue produced in low-temperature roasting-acid leaching pretreatment process of refractory gold concentrates

To provide a theoretical basis for a suitable process to extract gold from refractory gold concentrates, process mineralogy on the acid leaching residue of gold calcine was studied by chemical composition, X-ray diffraction, scanning electron microscopy-energy spectrum, and mineral dissociation analysis. The results showed that the acid leaching residue contained Au 68.22 g/t, Ag 92.71 g/t, Fe 0.44%, As 0.10%, and S 0.55%. Gold and silver minerals existed as native gold, argentite, and proustite. Quartz, the main gangue mineral, accounted for 78.33wt/%. The dissociation degree analysis showed that the proportions of monomer and exposed gold in acid leaching residue were 96.66wt%. The cyanidation results showed that the cyanide gold leaching rate of acid leaching residues was close to 100wt%. However, the maximum cyanide gold leaching rate of gold calcine was only 85.31wt%. This suggests that acid leaching can increase the gold dissolution rate in the cyanide process.     

Effect of Ce addition on microstructures and mechanical properties of A380 aluminum alloy prepared by squeeze-casting

The effect of cerium (Ce) addition on the eutectic Si, β-Al₅FeSi phase, and the tensile properties of A380 alloy specimens prepared by squeeze-casting were studied by optical microscopy (OM), scanning electron microscopy (SEM), and X-ray diffraction (XRD). The experimental results showed that Ce more effectively modified the eutectic Si and refined the β-Al₅FeSi. The refinement effect significantly increased under a specific pressure of 100 MPa with the addition of Ce from 0.1wt% to 0.9wt%. In contrast, the average length and the aspect ratio of the eutectic Si and β-Al₅FeSi exhibited their optimal values when the content of the added Ce was greater than 0.5wt%. Needle-like Al8Cu4Ce was precipitated with the addition of excessive Ce; hence, the mechanical properties of A380 gradually decreased with increasing Ce content in the range from 0.3wt% to 0.9wt%.     

New testing methodology for the quantification of rock crushability: Compressive crushing value (CCV)

Crushing is a size reduction process that plays a key role in both mineral processing and crushing-screening plant design. Investigations on rock crushability have become an important issue in mining operations and the manufacture of industrial crusher equipment. The main objective of this research is to quantify the crushability of hard rocks based on their mineralogical and mechanical properties. For this purpose, the mineralogical, physical, and mechanical properties of various hard rocks were determined. A new compressive crushing value (CCV) testing methodology was proposed. The results obtained from CCV tests were compared with those from mineralogical inspections, rock strength as well as mechanical aggregate tests. Strong correlations were found between CCV and several rock and aggregate properties such as uniaxial compressive strength (UCS), the brittleness index (S₂₀), and aggregate impact value (AIV). Furthermore, the relationship between the mineralogical properties of the rocks and their CCVs were established. It is concluded that the proposed testing methodology is simple and highly repeatable and could be utilized as a pre-design tool in the design stage of the crushing process for rock quarries.     

Microstructure and electrolysis behavior of self-healing Cu-Ni-Fe composite inert anodes for aluminum electrowinning

The microstructure evolution and electrolysis behavior of (Cu₅₂Ni₃₀Fe₁₈)-xNiFe₂O₄ (x=40wt%, 50wt%, 60wt%, and 70wt%) composite inert anodes for aluminum electrowinning were studied. NiFe₂O₄ was synthesized by solid-state reaction at 950℃. The dense anode blocks were prepared by ball-milling followed by sintering under a N₂ atmosphere. The phase evolution of the anodes after sintering was determined by scanning electron microscopy and energy-dispersive X-ray spectroscopy. The results indicate that a substitution reaction between Fe in the alloy phase and Ni in the oxide phase occurs during the sintering process. The samples were also examined as inert anodes for aluminum electrowinning in the low-temperature KF-NaF-AlF₃ molten electrolyte for 24 h. The cell voltage during electrolysis and the corrosion scale on the anodes were analyzed. The results confirm that the scale has a self-repairing function because of the synergistic reaction between the alloy phase with Fe added and the oxide phase. The estimated wear rate of the (Cu₅₂Ni₃₀Fe₁₈)-50NiFe₂O₄ composite anode is 2.02 cm·a-1.     

Complementation in the composition of steel slag and red mud for preparation of novel ceramics

A method for preparing novel ceramics was developed in this study. Different ratios red muds were added to steel slags to optimize the preparation of novel ceramics by a traditional ceramic preparation process. The sintering mechanism, microstructure, and performance were studied by X-ray diffraction techniques, scanning electron microscopy, and combined experiments of linear shrinkage, water absorption, and flexural strength. The results confirmed that red mud can reduce the volumetric instabilities through the complementarity of red mud and ferroalloy slag. The crystal phases in the ceramics are all pyroxene group minerals, including diopside ferrian, augite, and diopside. The flexural strength of the ceramic that contains 40wt% red mud and was prepared at the optimal sintering temperature (1140℃) is greater than 93 MPa; its corresponding water absorption is less than 0.05%.     

Leaching behavior of V,Pb, Cd,Cr, and As from stone coal waste rock with different particle sizes

This paper investigates the leaching behavior of heavy metals (V, Pb, Cd, Cr, and As) from stone coal waste rocks with various particle sizes using dynamic leaching experiments. The results show that the dissolved concentrations of V and As initially increased and then slightly decreased as time progressed and that the dissolved concentrations of Pb, Cd, and Cr were high in the early stage before decreasing. The particle size of the stone coal waste rocks strongly influenced the heavy metal concentration in the leaching solutions. The effects of the particle size of the stone coal waste rocks on the dissolved concentrations of V, Pb, and As decreased in the order fine fraction > medium fraction > coarse fraction, and the effects of particle size on the dissolved concentrations of Cr and Cd decreased in the order medium fraction > coarse fraction > fine fraction and coarse fraction > medium fraction > fine fraction, respectively. The quantities of heavy metals dissolved from the stone coal waste rock with fine particle sizes were observed to decrease in the order V (17104.36 μg/kg) > As (609.41 μg/kg) > Pb (469.24 μg/kg) > Cr (56.35 μg/kg) > Cd (27.52 μg/kg), and the dissolution rates decreased in the order As (2.96%) > Pb (0.93%) > V (0.35%) > Cd (0.25%) > Cr (0.01%). The specific surface area, pore size of the stone coal waste rocks, and chemical forms of heavy metals also influenced the release of heavy metals from the stone coal waste rocks. Kinetic analysis showed that the dissolution of heavy metals fundamentally agreed with the rate equation controlled by the shrinking core model. The results of this study are expected to serve as a reference for the evaluation of heavy metals contamination from stone coal waste rocks.